US] Nema23 stepper motor 435oz roundshaftdriver DQ542MA 18-50V+Power supply350w

Description

This Item includes:
The Item includes:
4PCS Nema 23 Stepper Motors WT57STH115-4204AP15
Single round shaft
4.2A 425oz-in
4PCS stepper motor drivers DQ542MA 4.2A 50VDC 125Microsteps
2PCS power supply 350W 36V
1PC brekout board&cable
as  free gifts
1, Stepper Motor
Model
Step angle
(
°
)
Motor Length
L(mm)
Rate Voltage
(V)
Rate Current
(A)
Phase Resistance
(
Ω
)
Phase Inductance
(mH)
Holding Torque
(kg.cm)
Lead Wire
(NO.)
Rotor
Inertia
(g.cm2)
Motor Weight
(kg)
WT57STH115-4204A
1.8
11
2
3.78
4.2
2.1
9
30
4
800
1.9
Specification
Manufacturer Part Number
WT57STH115-4204A
Step Angle
1.8°
Holding Torque
3.0Nm(425oz.in)
Rated Current/phase
4.2A
Phase Resistance
0.9ohms
Recommended Voltage
36
-48V
Inductance
3.8mH±20%(1KHz)
Weight
1.8kg
Drawing
Wire Connection
2. Stepper Motor Driver DQ542MA
DQ542MA is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC.
It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current.
This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration.
Holding torque when DQ542MA runs under high speed, is also significantly higher than the other two-phase driver, what’s more,
the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine,
CNC machine, Computer embroider machine, packing machines and so on.
Features:
l
High performance, low price
l
Average current control, 2-phase sinusoidal output current drive
l
Supply voltage from 18VDC to 50VDC
l
Opto-isolated signal I/O
l
Overvoltage, under voltage, overcurrent, phase short circuit protection
l
15 channels subdivision and automatic idle-current reduction
l
8 channels output phase current setting
l
Offline command input terminal
l
Motor torque is related to speed, but not related to step/revolution
l
High start speed
High holding torque under high speed
Electrical specification:
Input
voltage
18-50VDC
Input current
＜
4A
Output current
1.0A
～
4.2A
Consumption
Consumption
：
80W
；
Internal Insurance
：
6A
Temperature
Working Temperature -10
～
45℃
；
Stocking temperature -40℃
～
70℃
Humidity
Not condensation, no water droplets
gas
Prohibition of combustible gases and conductive dust
weight
300GS
3.POWER SUPPLY 350W 36V
350W Single Output Switching Power Supply
AC input range selected by switch.
Protections:short circuit/overload/over voltage/over temperature
100% full load burn-in test
Low cost,high reliability
1 year warranty
Size: 215*115*50mm
Weight:1.05kg
AC input voltage range: 90
～
132VAC/180
～
264VAC
AC inrush current: cold start 25A/115V,50A/230V
DC adjustment range:±10% rated output voltage
Overload protection:105%
～
135%, hiccup mode, auto recovery
Setup,rise,hold up time: 200ms,50ms,20ms/230VAC at full load
Working temperature and humidity:-10℃
～
+60℃
；
20%
～
90 %RH
Model
DC output voltage,
Current range
Voltage tolerance
Ripple
&Noise
Efficiency
S-350-36
36V,0
～
9.7A
±1%
150mV
83%
4. Breakout Board
Set pins according to software as follows:
Output pin: P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17.
l
P2 – X axis Pulse, P3 – X axis Direction
l
P4 – Y axis Pulse, P5 - Y axis Direction
l
P6 – Z axis Pulse, P7 – Z axis Direction
l
P8 - A axis Pulse, P9 - A axis Direction
l
P14 - B axis Pulse, P1- B axis Direction
l
P16 - C axis Pulse, P17- C axis Direction
Input pin: P10 ,P11, P12, P13, P15
Set them for Emergency Stop and X Y Z Limit switch